Search
Filters

73-76 Cadillac VIR - REBUILT

SKU: 15-VIR-f
Make: CADILLAC
*

Not all cores are eligible for credit.  Details in overview below.

$185.00

A rebuilt original VIR assembly (part #15-5112/also replaces 15-560).

Has been hand-built, pressure & function tested and is ready to be installed & used.

The upper and lower shells (4 3/4" length) have been gold-zinc plated.

PLEASE NOTE - We try to keep this rebuilt & ready to ship, but often these valves are built-to-order and may take up to 5 business days to ship from the time payment is completed.

CONVERTING TO 134A?  Because the VIR is not adjustable, it is not recommended for use with 134a.  Instead, we recommend our VIR eliminator kit.  (Original Air's part #15-211)

PLEASE NOTE - ALL REBUILT VIR'S ARE BUILT TO ORDER AND CAN TAKE UP TO 5 BUSINESS DAYS TO SHIP.  PLEASE CALL PRIOR TO PURCHASING IF YOU NEED IT SOONER AND WE'LL DO OUR BEST TO ACCOMODATE YOUR REQUEST.

A rebuilt original VIR assembly (part #15-5112/also replaces 15-560).

Has been hand-built, pressure & function tested and is ready to be installed & used.

The upper and lower shells (4 3/4" length) have been gold-zinc plated.

PLEASE NOTE - We try to keep this rebuilt & ready to ship, but often these valves are built-to-order and may take up to 5 business days to ship from the time payment is completed.

CONVERTING TO 134A?  Because the VIR is not adjustable, it is not recommended for use with 134a.  Instead, we recommend our VIR eliminator kit.  (Original Air's part #15-211)

PLEASE NOTE - ALL REBUILT VIR'S ARE BUILT TO ORDER AND CAN TAKE UP TO 5 BUSINESS DAYS TO SHIP.  PLEASE CALL PRIOR TO PURCHASING IF YOU NEED IT SOONER AND WE'LL DO OUR BEST TO ACCOMODATE YOUR REQUEST.

Products specifications
Years 73
Years 74
Years 75
Years 76
Category VALVES - A/C
Category FILTER-DRIERS & ACCUMULATORS
Manufacturer CADILLAC

CONVERTING GENERAL MOTORS CARS

TO 134a

Until 1995, most cars with air conditioning used R-12 Freon refrigerant that is said to have a negative side effect of damaging the ozone layer and is no longer produced in most countries. since then, the industry standard has been R134a, which is an efficient replacement.  Contrary to popular belief, most cars originally equipped with R-12 can be converted to 134a and still keep you just as cool.

 

1955-61 Models with Hot Gas Valve (aka By Pass or Hot Gas By Pass Valve)

The Hot Gas Valve is most often found mounted to the compressor, though some cars have it mounted back near the evaporator. The front half of it looks like a bullet. (Click here for a typical photo)

Minimum Requirements

  • Change or restore the filter-drier.
  • Drain the compressor oil and recharge with 134a compatible oil. (PAG or Ester Oil)
  • Insure that the system is clean and free of contaminants (Depending on component condition, this may be a simple matter of blowing out with compressed air or liquid flushing with an air-conditioning flushing agent)
  • Replace or restore all rubber hoses with barrier hose.
  • Rebuild hot gas valve.
  • Install 134a charge port adapters.
  • Charge with 134a between 70-80% of the original R12 charge amount. Note: Hot gas valve will need to be adjusted during the charging process to properly adjust the low side by-pass pressure to 20psi.
  • Replace any o-rings with 134a compatible.

Recommended:

  • Install hi/lo pressure switch

HELPFUL HINTS

  • Ignore the sight-glass. A properly charged 134a system will likely show bubbles in the sight-glass.
  • Typical 134a charge rate will be approximately 70-80% of the factory R12 charge amount.

 

1962-66 Models with Suction Throttling Valve (aka STV)

The suction throttling valve is installed on the evaporator, near the firewall.(Click here for a typical photo)

Minimum Requirements

  • Change or restore the filter-drier.
  • Drain the compressor oil and recharge with 134a compatible oil. (PAG or Ester Oil)
  • Insure that the system is clean and free of contaminants (Depending on component condition, this may be a simple matter of blowing out with compressed air or liquid flushing with an air-conditioning flushing agent)
  • Replace or restore all rubber hoses with barrier hose.
  • Rebuild suction throttling valve.
  • Install 134a charge port adapters.
  • Charge with 134a between 70-80% of the original R12 charge amount. Note: Suction throttling valve will need to be adjusted during the charging process to properly adjust the low side by-pass pressure to 20psi.
  • Replace any o-rings with 134a compatible.

Recommended:

  • Install hi/lo pressure switch

HELPFUL HINTS

  • Ignore the sight-glass. A properly charged 134a system will likely show bubbles in the sight-glass.
  • Typical 134a charge rate will be approximately 70-80% of the factory R12 charge amount.

 

1966-73 Models with POA Valve

The POA Valve is installed on the evaporator, near the firewall. (Click here for a typical photo)

Minimum Requirements

  • Change or restore the filter-drier.
  • Drain the compressor oil and recharge with 134a compatible oil. (PAG or Ester Oil)
  • Insure that the system is clean and free of contaminants (Depending on component condition, this may be a simple matter of blowing out with compressed air or liquid flushing with an air-conditioning flushing agent)
  • Replace or restore all rubber hoses with barrier hose.
  • Install 134a charge port adapters.
  • Have POA valve recalibrated/rebuilt for 134a, or replaced with a POA Delete Kit
  • Charge with 134a between 70-80% of the original R12 charge amount.
  • Replace any o-rings with 134a compatible.

Recommended:

  • Install hi/lo pressure switch

HELPFUL HINTS

  • Ignore the sight-glass. A properly charged 134a system will likely show bubbles in the sight-glass.
  • Typical 134a charge rate will be approximately 70-80% of the factory R12 charge amount.

 

1973-76 Models with VIR

The VIR is installed on the evaporator, near the firewall. (Click here for a typical photo)

Minimum Requirements

  • Change desiccant in VIR.
  • Drain the compressor oil and recharge with 134a compatible oil. (PAG or Ester Oil)
  • Insure that the system is clean and free of contaminants (Depending on component condition, this may be a simple matter of blowing out with compressed air or liquid flushing with an air-conditioning flushing agent)
  • Replace or restore all rubber hoses with barrier hose.
  • Install 134a charge port adapters.
  • Charge with 134a between 70-80% of the original R12 charge amount.
  • Replace any o-rings with 134a compatible.

Recommended:

  • Install hi/lo pressure switch
  • Install our VIR Eliminator (strongly recommended when converting to 134a), purchase a rebuilt VIR or let us rebuild yours.

HELPFUL HINTS

  • Ignore the sight-glass. A properly charged 134a system will likely show bubbles in the sight-glass.
  • Typical 134a charge rate will be approximately 70-80% of the factory R12 charge amount.

 

1977-Newer Models with Accumulator

The accumulator is most often installed on the evaporator, near the firewall. (Click here for a typical photo)

Minimum Requirements

  • Change or restore the accumulator.
  • Drain the compressor oil and recharge with 134a compatible oil. (PAG or Ester Oil)
  • Insure that the system is clean and free of contaminants (Depending on component condition, this may be a simple matter of blowing out with compressed air or liquid flushing with an air-conditioning flushing agent)
  • Replace or restore all rubber hoses with barrier hose.
  • Install 134a charge port adapters.
  • Charge with 134a between 70-80% of the original R12 charge amount.
  • Replace any o-rings with 134a compatible.

Recommended:

  • Install hi/lo pressure switch
  • Upgrade the standard orifice-tube to a variable orifice tube.

HELPFUL HINTS

  • Ignore the sight-glass. A properly charged 134a system will likely show bubbles in the sight-glass.
  • Typical 134a charge rate will be approximately 70-80% of the factory R12 charge amount.
Products specifications
Years 73
Years 74
Years 75
Years 76
Category VALVES - A/C
Category FILTER-DRIERS & ACCUMULATORS
Manufacturer CADILLAC
Product tags